Triumph Slant-4 engine

Triumph Slant-4
place image here in 300 pixels
Engine
Manufacturer	Triumph
aka	Type aka here, not up there
Type	Petrol
Production/Introduction	produced/introduced from when to when
Status	Discontinued
Displacement	1.7 L (1709 cc)
Aspiration	write its type of aspiration
Configuration	slanted straight
Cylinders	four (4)
Fuel System	write if it is injected or carburated and the system used
Lubrification	indicate the engine's type of lubrification
Output	N/A hp @ N/A rpm N/A lb-ft. of torque @ N/A rpm
Bore	in inches
Stroke	in inches
Compression	write compression ratio here
In. Valves	in inches
Ex. Valves	in inches
Firing Order	Firing order of cylinders
Left Bank	Write which cylinders are in this bank (write N/A if it it is inline)
Right Bank	(same as above)
Length	in inches
Diameter	in inches
Width	in inches
Height	in inches
Dry Weight	lbs. / kg.
Fuel Consumption	city/highway (mpg & km/L)
Emission/s	CO: g/km CO2: g/km NOx: g/km Hydrocarbon: g/km Particulate: g/km
Chief Engineer	Lewis Dawtry and Harry Webster

The Triumph Slant-4 is an engine developed by Triumph. According to Triumph historians Graham Robson and Richard Langworth in Triumph Cars, the complete story, the engine was developed in-house by a design team led by Lewis Dawtry and Harry Webster.

The UK engineering and consultancy company Ricardo, which did have a general engine-development contract with Triumph, was not directly involved with its design, but was usually kept informed of anything new being planned. Ricardo was involved in developing a new engine for Saab, as a replacement for their aging Saab two-stroke and V4 units. When that development proved too expensive and risky to produce, Ricardo, knowing the slant-4 was almost ready for production, brought Saab into contact with Triumph.

Saab first used the Triumph Slant-4 at 1.7 L (1709 cc) for the Saab 99. Only later, as production capacity increased, did it become available in Triumphs. Development by Saab continued into the 1990s. The engine is a straight-4 with the cylinders tilted at 45 degrees (actually in effect half of the Triumph V8 that was used in the Triumph Stag).

The engine was used by Triumph in the Dolomite 1850, the Dolomite Sprint, and the TR7. It was also used by Panther in the Dolomite-based Rio (1975-1977). Triumph ended manufacture of the engine when the TR7 was discontinued in 1981.

Sprint version[]

Triumph added unique SOHC 4-valve cylinder heads to the Slant-4 for 1973's Dolomite Sprint. This is regarded as the first mass-produced multi-valve car engine.

Saab B engine[]

Saab later increased the engine size to 1.85 L and in 1972 the company brought production in-house (to Scania) for the 2.0 L B version. This engine shared much with the original Triumph design, including bore centers and bearings, but was substantially redesigned. The Saab B engine was replaced by the related Saab H engine.

Photos[]

Unique Attributes[]

If there are any features of this vehicle that sets it apart from other vehicles in its class, then mention those unique attributes here.

Criticisms[]

Please make sure to keep critiques in a third-person point of view. If using criticisms from a reputable automotive source, then please make sure to cite the quote.

Worldwide[]

If the vehicle is sold in other markets worldwide, then this is the section to mention that information. Also, mention if the <MODEL> goes by another name in these other markets.

Design quirks and oddities[]

Refer to any pop-culture tidbits about the vehicle in this section.

Awards[]

List out notable awards that the model has recieved while in production. Boldface the company or orgainization that gives out the award, and Italicize the name of the award.

External Links[]

Please include any external sites that were used in collaborating this data, including manufacturer sites, in this section.